Skip to content

Fully insured, over 10 years' experience, free consults: (972) 945-9592

(972) 945-9592
Two installers in caps and jeans lift a new dark fiberglass entry door with decorative glass and sidelites into the front opening of a brick house porch.

ServicesEntry Doors

Entry Doors in Terrell, TX

A new front or side door from us arrives as a complete prehung unit, frame and sill included. We set it level, flash the threshold and finish the trim by hand. The result latches with a light push, keeps drafts out and suits the face of your home.

Why Replacing the Whole Door Makes Sense

Few parts of your home move as often as the front door. It opens and closes many times a day, faces sun and wind-driven rain, and holds the lock you count on at night. Once the slab bows, the bottom of the frame softens or the weatherstrip stops touching the jamb, tightening hinges is a short-term fix.

A full unit replacement, with new jambs and a new sill, deals with the reason the door failed. We prepare the opening, then fit the prehung door so the reveal is even all the way around, the seal presses evenly and the deadbolt slides home on its own.

We start by looking at your door in person. Then we tell you what caused the trouble and which options are worth your money, without the sales talk.

What Your Entry Door Replacement Includes

Removal of the old unit

We take out the old slab, jambs and threshold carefully to protect the surrounding brick, siding and interior trim. The old door leaves with us.

Opening inspection and prep

With the frame out, we check the subfloor and framing at the base of the opening, where water damage usually hides. You see what we find before we go further.

Sill pan and flashing

A sloped sill pan and flashing tape go in under the new threshold so any water that gets past the door drains out instead of into the floor.

Setting, shimming and insulating

The new prehung unit is shimmed plumb and square, fastened through the jambs, and the gap is filled with low-expansion foam so the frame does not bow.

Hardware, trim and finish

We install the handleset and deadbolt, adjust the strike plates, and finish exterior trim and caulk so the door looks built in, not added on.

Cleanup

Floors are covered during the work, and we vacuum and wipe down before we leave.

How to Tell Your Entry Door Is Ready to Go

  • Light or air leaking around the slab

    A glow along the edges at dusk, or a cold or hot draft on a breezy day, means the seal or the frame has slipped. On an older unit neither is easy to bring back.

  • Spongy wood near the floor

    Water damage tends to begin at the lower jambs and beneath the sill. Push a screwdriver into the wood; if it gives, the frame has rotted beyond use.

  • A door that binds or a lock that resists

    Rubbing in summer, rattling in winter, or needing to pull up on the handle before the deadbolt turns all suggest the frame is no longer square.

  • Worn finish or a damaged skin

    Years of afternoon sun can fade and peel a finish and twist a wood slab. Dents or rust spots on an older steel door let moisture reach the core.

  • Cloudy glass in the door

    Haze trapped between the panes of a decorative lite tells you the seal is gone. Many older doors were not built for the glass to be swapped separately.

How the Job Runs

  1. 1

    Free in-person consultation

    We measure the rough opening, look at the sill and framing, and talk through materials, glass and hardware with samples in hand. You get a written quote that lists each part of the job.

  2. 2

    Ordering the door

    Your door is built to the measured size and swing, with the finish and glass you chose. We confirm the delivery date with you before scheduling the install.

  3. 3

    Installation day

    Most single doors are out and back in during one working day. The opening is only open for a few hours, and your home is closed up and locked before we leave.

  4. 4

    Walkthrough

    We show you how the door latches and seals, hand you the keys, and explain any care the finish needs. If something does not close the way it should, we adjust it while we are there.

What Sets the Cost of a New Entry Door

Two things decide most of the number: the door you pick and the condition of the opening it goes into. We price your project after measuring in person, so the quote reflects your actual door rather than an estimate from a photo. For those who want it, we offer $0 Down on the whole project and 0% Financing options.

Slab material
Steel costs the least and makes a strong, secure door. Fiberglass shrugs off dents and rust and stays stable in heat. Solid wood gives the warmest grain and finish, with more upkeep over the years.
Sidelites and transoms
A single slab is the simplest unit. Adding one or two sidelites, or a transom overhead, widens the frame and brings in more glass, which raises both material and labor.
Glass choices
Clear, frosted, textured and leaded inserts are each priced differently, and lites with built-in blinds add to it.
What is under the old threshold
If the framing or subfloor beneath the sill has softened from water, it must be rebuilt so the new unit has solid footing. You get photos of the damage and a separate line on the quote for that work, agreed before we touch it.
Size, hardware and finish
Openings outside standard sizes call for a custom-built unit. Upgraded handlesets, smart locks and factory-applied stain or paint also move the price.

Common Questions About Entry Doors

Something not covered here? (972) 945-9592

Which holds up better in strong sun, steel or fiberglass?

Fiberglass, in most cases. It will not rust or dent, and it stays flat through big temperature swings. Steel remains a good, economical pick for an entry under a porch roof or on a shaded side of the house. We match the material to how much sun your door actually gets.

Is it possible to swap only the slab and reuse the existing frame?

Only when the frame is solid, square and correctly sized, which is less common on older doors. Usually the jambs and sill have shifted or taken on water, and a new slab hung in a tired frame will not seal well. A full prehung unit tends to last longer, and we tell you plainly which route your door needs.

How long is the doorway open during installation?

A few hours on a typical single door. We remove the old unit and set the replacement during one visit, so the opening is never left overnight. Before our crew leaves, the new door is hung, latched and locked.

Will the new door look right with my trim and paint?

We fit and seal the exterior trim so the door sits cleanly in the wall. Many units arrive factory finished in the color you choose. If yours will need paint or stain to match the house, we explain what that takes at the consultation.

Can a storm door be added when the entry door goes in?

Yes. Installing both on the same visit is straightforward, and a storm door adds ventilation and a layer of protection for the new finish. Our Storm Doors page covers the styles we offer.

Ready to See What Your Door Needs

We will look at your entry door, explain what is wrong and walk you through materials and price in person. No pressure, just straight answers.